Tape & Moulding Hold Down Tools

sort by:
  • 1
view:

1-1/2" Orange Glass Tape

IP GOR1201

$7.00

This tape is designed to perform as a temporary holding mechanism for rubber/plastic mouldings used on automotive glass. It is designed to temporarily retain the rubber/ plastic moulding in the proper position while the urethane is curing. This tape leaves no residue, repels water, and is translucent so you can see if it is holding the moulding in place. Gold Glass Group provides a limited paint delamination guarantee.

Each roll is 108 feet long and 1-1/2" wide.

1-1/2" Orange Glass Tape • 3" Perforations

IP GOR1224

$8.00

This tape is designed to perform as a temporary holding mechanism for rubber/plastic moldings used on automotive glass. It is designed to temporarily retain the rubber/ plastic molding in the proper position while the urethane is curing. This tape leaves no residue, repels water, and is translucent so you can see if it is holding the molding in place. Gold Glass Group provides a limited paint delamination guarantee. 

Each roll is 108 feet long and 1-1/2".

1-1/2" Orange Glass Tape • 6" Perforations

IP GOR1226

$8.00

This tape is designed to perform as a temporary holding mechanism for rubber/plastic moldings used on automotive glass. It is designed to temporarily retain the rubber/ plastic molding in the proper position while the urethane is curing. This tape leaves no residue, repels water, and is translucent so you can see if it is holding the molding in place. Gold Glass Group provides a limited paint delamination guarantee.

GOR1226 is 108 feet long and 1-1/2" wide.

1-1/2" Orange Glass Tape • 6" Perforations

IP GOR1206

$7.00

This tape is designed to perform as a temporary holding mechanism for rubber/plastic moldings used on automotive glass. It is designed to temporarily retain the rubber/ plastic molding in the proper position while the urethane is curing. This tape leaves no residue, repels water, and is translucent so you can see if it is holding the molding in place. Gold Glass Group provides a limited paint delamination guarantee. 

Each roll is 108 feet long and 1-1/2".

2" Orange Glass Tape

IP GOR0206

$10.00

This tape is designed to perform as a temporary holding mechanism for rubber/plastic moldings used on automotive glass. It is designed to temporarily retain the rubber/ plastic molding in the proper position while the urethane is curing. This tape leaves no residue, repels water, and is translucent so you can see if it is holding the molding in place. Gold Glass Group provides a limited paint delamination guarantee. 

Each roll is 108 feet long and 2" wide.

Moulding Hold Down Tool

IP PHT318

$10.00

The corners on today’s moldings will often raise up and leave an unsightly gap under them. Taping these moldings down can be disastrous because the tape will sometimes attack the paint and, in the worst case, remove it. Our molding hold down tool is attached to a vacuum cup. Pressure is then applied to each end of the tool by tightening the wing nut and putting upward pressure on the vacuum cup, thereby putting downward pressure on both ends. Made of high impact plastic.

TopSTOP™

IP LJ1260

$16.00

Holds the glass up while the urethane is curing.

Most of today’s urethanes start curing as soon as the windshield is installed. Since most vehicles do not have lower stops, it is necessary to tape the windshield in place while the urethane starts curing. With TopSTOP™, you put the vacuum cups on the windshield before you set it in place. As soon as the glass is set, you attach the other end of the vacuum cups to the top of the vehicle. By the time you have finished assembling the vehicle, the urethane is usually cured enough to hold it in place. You then remove the TopSTOPs™. The wires are bright orange so you will not overlook them and leave them attached to the vehicle.

Two per set.

  • 1