You asked: What is the typical viscosity of automatic transmission fluid?

Temp. [°C] Dyn. Viscosity [mPa.s] Kin. Viscosity [mm²/s]
217.29 247.39
10 118.06 135.42
20 70.04 80.93
30 44.70 52.04

What weight oil is transmission fluid?

Transmission Fluid is essentially thin hydraulic oil. In order to effectively lubricate the delicate parts of the system, the viscosity of the oil is kept low – generally around 0W/5 or 5W/10. Most importantly it needs to be relatively free flowing in order to transmit power from the engine to the transmission.

What is the viscosity of dexron III?

Performance Specifications

TYPICAL PROPERTIES ATF
KINEMATIC VISCOSITY CST @ 40°C 37
KINEMATIC VISCOSITY CST @ 100°C 7.3
VISCOSITY INDEX (D2270) 173
BROOKFIELD VISCOSITY @ -40°C 17000

Is ATF low viscosity?

Low viscosity ATF is the cutting edge of ATF technology. It has active chemistry that allows it to not only last longer than high viscosity ATF but also protect the transmission for tens of thousands of miles. On top of calling for thinner fluid, some OEMs have extended their recommended drain intervals.

What viscosity is dexron ATF?

Property

IT IS INTERESTING:  Your question: Does Toyota use Mazda engines?
Property
Brookfield Viscosity @ -40 C, mPa.s, ASTM D2983 11500
Color, Visual Red
Flash Point, Cleveland Open Cup, °C, ASTM D92 220 (428)
Kinematic Viscosity @ 100 C, mm2/s, ASTM D445 5.83

What type of automatic transmission fluid should I use?

Dexron III/Mercon – This is one of the most common fluids on the market. Most GM and Ford units call for this type of ATF, as well as many imports. If your owners manual recommends any form of Dexron, or any Mercon – other than Mercon V – this is the fluid you want.

Is differential oil the same as transmission fluid?

Differentials use gear oil/fluid. A manual transmission also uses gear oil but the viscosity may be a bit different. In an automatic transmission, definitely not; the fluid is much thinner and is called ATF – automatic transmission fluid.

What viscosity is transmission fluid?

ATF III – Mineral automatic transmission fluid

Temp. [°C] Dyn. Viscosity [mPa.s] Kin. Viscosity [mm²/s]
217.29 247.39
10 118.06 135.42
20 70.04 80.93
30 44.70 52.04

What is the difference between dexron III and dexron VI?

But to mention the biggest difference between Dexron-III and VI is that of “viscosity”. Dexron-VI is much thinner. With the less updated base, Dex-III provides less shelf life than VI.

Is dexron 3 the same as ATF 4?

Dexron IV was an upgraded version of Dexron III, which was used by GM only briefly. … GM considers Dexron VI to be “backward compatible,” meaning GM recommends it for use in any vehicle that originally used any earlier version of Dexron and that it can be mixed with them.

IT IS INTERESTING:  Frequent question: Who invented automatic windshield wipers?

What is low viscosity transmission fluid?

To conform with global trends, Totachi low viscosity ATFs are low viscosity fluids which reduce inner resistance loss, thus decreasing fuel consumption. Totachi low viscosity ATFs provide full protection of all parts and reliable performance of automatic transmission in high loads.

What is a good viscosity index?

Typical mineral-oil fluids used in hydraulics have a viscosity index of around 100, although products range from below 100 to well beyond 200. The best oils with the highest VIs remain stable and don’t vary much in viscosity over a wide temperature range.

What is the viscosity of 90 weight gear oil?

Typical Properties

Mobilube HD LS 80W-90 80W-90 85W-140
Viscosity, ASTM D 445
cSt @ 40ºC 136 328
cSt @ 100ºC 14.5 25.3
Viscosity Index, ASTM D 2270 105 97
Car repair school